- UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL HOW TO
- UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL SOFTWARE
- UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL CODE
- UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL DOWNLOAD
- UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL WINDOWS
BTECH sells many different Nagoya antennas that simply screw right into your radio and improve the signal of your handheld. You might, for example, replace the antenna that comes with your handheld transceiver with a Nagoya antenna. One way to overcome this is by using a better antenna. It has to be replaced with the one that is to be found on the internet, or on the right side of this page (My Place). Perhaps the most common reason is that your signal simply isn’t strong enough. There are other reasons that you may not be able to access a repeater. DCS tones are, however, very rarely used on the amateur radio bands. A DCS tone is similar to a CTCSS tone in that it is sub-audible and opens the squelch of a repeater when a station is trying to access it.
UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL CODE
In some cases, a repeater may require a Digital Code Squelch, or DCS, tone to access it. For more information on how CTCSS tones work, see, “Get your CTCSS tones right to access repeaters.” CTCSS tones allow repeaters o receive particular signals and reject others. Once you’re sure that you have the offset correct, check to see if the repeater requires that your radio transmit a CTCSS to access it. In addition to getting the offset correct, keep in mind that the transmit frequency may be higher or lower than the receive frequency. On the 70-cm band, the standard offset is 5 MHz. On the 2-meter band, the standard offset is 600 kHz. The offset is the difference between the repeater’s receive frequency and the transmit frequency. If you can hear a repeater, but your signal is not accessing the repeater, the first thing to check is to make sure that your offset is set properly. The correct answer is D) All of these choices are correct. It is not known how much of this information is relevant to other firmware versions, models or clones from other manufacturers.
UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL SOFTWARE
But when it comes to emergency preparedness, this is where the software shines. It can be used to program a wide variety of radios, including the Baofeng.
Which of the following could be the reason you are unable to access a repeater whose output you can hear? (T2B04) If this does not resolve the issue, review the software recovery procedure located at. CHIRP is a free, open-source tool for programming your amateur radio. This is such a frequent problem, that there’s even a question (T2B04) on the Technician Class exam that addresses this issue:
When this happens, the first question out of their mouths is, “Why can’t I hit the repeater?”
After programming the radio, they’re often able to hear the repeater, but not access it. My main interest was to program the GMRS channels into the radio to be used in channel mode, and in CHIRP this is easy to do by selecting Radio -> Import from stock config -> US FRS and GMRS Channels and then uploading to the radio.One of the first things that many new radio amateurs do is to purchase a handheld radio, like the BTECH UV-5X3 (right), to talk with their friends on a local repeater.
Then select Program -> Read from radio and you should be able to extract data from your device. Do not worry – there is English interface available, to switch to it, click on the second-last menu and select English from the drop-down.
UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL WINDOWS
There were also files named WP970I_CPS, WP970Setup I am not sure in which ways they are different from the one I downloaded.Īfter installation, it launches with all-Chinese interface, which on my Windows installation resulted in question marks for all menu names and menu items. I downloaded the file named “WP970I Setup”, mainly because it specified Chinese/English as language.
UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL DOWNLOAD
This software can be downloaded from Baofeng: go to and select Download -> Programming Software. If they dont, use menu 28 to delete the channels.Remember that programming to an already programmed channel will only overwrite the transmitting memory not the receiving memory.Even if it is a simplex channel, the UV-5R will always write the same frequency on both the rx and tx registers. CHIRPĬHIRP is easy: once you’ve figured out the COM port where the radio is listening, select UV-82WP as the radio model, and it should work. It took me some time to figure it out, and here is a summary. There are two ways to connect to the radio.
UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL HOW TO
I bought a couple of Baofeng UV-9R radios with a computer communication cable, but I could not find instructions on how to program the radios from a computer.